Posts tagged: dryer-outlet

3-Wire and 4-Wire Dryer Receptacles

By admin, June 21, 2012 9:01 am
Question: 3-Wire and 4-Wire Dryer Receptacles
I’m often asked how to wire dryer outlets, how to convert the wiring either from 3-wire to 4-wire, or to convert the wiring from 4-wire to 3-wire. Some people feel overwhelmed when they encounter these circumstances. Not to fear though, I have the answers on how to wire and convert the wiring to make your dryer work perfectly and safely.
Answer: First of all, to properly wire a dryer outlet (receptacle), you’ll need to follow my guide on How To Wire a Dryer Outlet. This step-by-step set of instructions will have you drying clothes in no time at all.

Then there’s the issue with converting the wiring from a three-wire dryer cord to four-wire cord. How is this possible? Well, in my guide on How To Change An Electric Dryer Cord From 3-Prong To 4-Prong Cords.

This is a great step-by-step guide and is easy to do yourself in just minutes.

Likewise, there’s a guide to covert the cords from 4-wire to 3-wire. In my guide on How To Convert Electric Clothes Dryer Cords From 4-Prong To 3-Prong.

If you simply want to learn how to wire a 3-pronged dryer outlet, simply follow my guide on How To Wire A Dryer Outlet. In it, I show you step-by-step instructions on the installation process. best online casino .

Lastly, here’s a how-to for a four-pronged dryer outlet installation.

Wiring Typical Laundry Circuit

By admin, September 26, 2011 10:31 am

It is commonplace for homes today to have one or more of three different laundry circuits. Each has its own unique assignment for supplying power to the laundry appliances. One is a 20-amp circuit designated to run the 120-volt power for the washing machine and the control power for the dryer. This circuit can also supply general-use devices. It is wired with 12-gauge wire and is usually type THHN or THWN wire. This is a dedicated circuit for the laundry room only.

The second is a 240-volt outlet that supplies a 30-amp circuit to feed an electric dryer. This circuit is wired with 10-gauge wire and is also THHN or THWN type wire. This feed is exclusively for and electric dryer and nothing else.

The third is one you may not have thought of. What would a laundry room be without a circuit for lighting? The lighting circuit may not be an independant circuit, and in fact, usually isn’t. It is likely it will be on the same circuit as an adjacent room or hallway.

With the following electrical wirng tips, you’ll be able to add an outlet, install a dryer outlet, or install a single-pole switch in no time.

How To Wire An Outlet

How To Wire A Dryer Outlet

How To Wire And Install Single-pole Switches

How To Wire A Dryer Outlet

By admin, September 7, 2011 5:51 pm

You can test a dryer outlet by using a multimeter. Insert the two test leads into the tester if they aren’t already installed. Turn the tester power on and set the selector to AC volts. Now adjust the setting to the 240-volt setting or the next highest setting. Insert the test leads into the two top “hot” slots in the receptacle. These are the two slots that are tipped at a 45 degree angle. The voltage at this point should read between 220-240 volts. Now read the voltage between each of the two hot leads to the neutral slot. It is the straight slot below the two “hot” slots. The voltage here should read between 110-120 volts. If all of these connections check out, you have a fully functioning dryer outlet.
Previous
  • Dryer Outlets – How To Strip The Wire
  • Stripping Individual Wire Conductors
  • How to Connect the Wires to the Terminals
  • How to Attach the Wire Clamp
  • How to Install a Dryer Outlet Cover Plate
  • How to Test a Dryer Outlet

Next

Wire a 4-Prong Dryer Outlets

By admin, September 6, 2011 8:02 am

4-prong dryer outlets are simple enough to wire if you have the proper material and tools to do the job. You’ll need at least a few of the following things to accomplish this task:

  1. Drywall Screws
  2. Screwdrivers
  3. Pliers
  4. Wire Strippers
  5. Razor Knife
  6. Linesman Pliers
  7. 240-volt, 4-Prong Dryer Outlet
  8. 10-3 With Ground Nonmetallic Sheathed Cable
  9. 2-Pole, 30-Amp Circuit Breaker

Difficulty: Easy
Time Required: Less Than 15 Minutes

Here’s How:

  1. Run a New Feed

    If your home is not already wired for a 4-prong outlet or if the feed is not equipped with two hot wire, a neutral, and a ground wire, you’ll need to run a new wire to feed the outlet. Install a 10-3 NM wire that has a ground wire included from the breaker panel to behind the dryer. Leave enough slack at each end to allow for proper connection.

  2. Mount The Dryer Outlet

    Remove the dryer outlet cover and remove the outlet electrical connection knockout. Install the nonmetallic sheathed cable into the outlet box, tighten the cable clamp, and attach the outlet to the wall.

  3. Wire The Dryer Outlet

    Strip the red and black wires and install the in the outer two connection points of the outlets, which is the two hot feeds of the outlet.

    Now strip and connect the white wire to the neutral connection, which is the terminal screw with the “L”-shaped terminal.

    Connect the bare copper ground wire to the ground terminal, which is the round terminal.

    Replace the dryer outlet cover plate and tighten the mounting setscrew.

  4. Connect The Wire To the Breaker

    Connect the red and black wires to the 2-pole, 30-amp breaker, the white wire to the neutral buss and the bare copper ground wire to the grounding buss.

    Turn on the breaker and test the outlet with a voltage tester or a digital multimeter.

Tips:

  1. Be sure you install 10 guage wire. It is rated for 30 amps. There’s no published evidence to suggest that detox treatments, kits or rituals have any effect on our body’s ability to eliminate waste products effectively..
  2. You’ll need a 2-pole, 30-amp breaker to feed this outlet.
  3. Place the outlet near the dryer because dryer cords come in four, five, and six foot lengths.

What You Need:

  • 4-Prong Dyrer Outlet
  • 10-3 Wire With a Ground
  • 2-Pole, 30-Amp Breaker
  • Razor Knife
  • Romex Connectors For The Outlet and Panel
  • Wire Strippers To Strip The Wires
  • Linesman Pliers To Cut The Wire
  • Pliers To Tighten The Connector Clamps
  • Screwdrivers